Why are heat and high-temperatures hindering solar photovoltaic potential in the MENA region?


By Carlo Maragliano, Ph.D., Head of R&D.

The Middle East and North Africa (MENA) region has become, in the last few years, the favorite target for solar renewable energy companies all over the world. The reason is straightforward: the region has the highest access to sunlight throughout the year when compared to any other region around the globe. To understand this point and its implications, let’s make a simple comparison between one of the sunniest cities in Europe, Madrid, and the capital of the United Arab Emirates, Abu Dhabi. If we look at the annual sunshine hours, which measure the amount of hours that the sun shines during one-year time, Madrid has approximately 2750 sun-hours, while Abu Dhabi has over 4100. Imagine now that you have a solar panel, and are asked where to install it to obtain the maximum power output. Where would you put it? In Abu Dhabi, off course! In the capital of the UAE, indeed, the same module could potentially produce up to 150% of the power that it would generate in Madrid. This should be enough encouragement to move all solar power generation businesses to the MENA region, right? However good these numbers, solar power growth in the MENA region has not yet lived up to global expectations.

Map_irradiance

So, what is hindering the great potential of solar PV in this region? One point is the heat. The MENA region is characterized by very high temperatures, which during the summer can even reach 50C. Why is that negative for solar PV? Solar panels loose a % of their efficiency as their operative temperature rises above 25C, which is the standard temperature at which they are tested to determine their “nominal” efficiency. Standard Si modules (which represent over 90% of the market) loose in average 0.6 % in power conversion efficiency for every C increase in their working temperature. This figure is widely known by the PV community as the temperature coefficient of the solar module. To put this in an example, a solar module with a proven efficiency of 20% at 25C, has at a working temperature of 60C an efficiency of only 15.8%, meaning that it loses more than 20% of its original capability of producing electricity. It is also important to note that the outside temperature is not the only factor that determines the operative temperature of a solar module. Under standard operation, a solar module, other than producing electricity, generates a lot of heat. Imagine that in a 20%-efficient solar module, almost 60% of the incoming energy is turned into heat. As this heat is not converted into electricity, it raises the temperature of the solar panel, thus negatively affecting its capability to produce electrical power. It is not unusual then that solar panels in the MENA region reach, during the summertime, temperatures above 75C. Under this condition, solar modules can loose over 30% of their original power conversion efficiency.

Can we work around this problem? The PV community has embarked on different paths to reduce heat-related losses. The first path consists in improving material quality with the scope of bringing down the temperature coefficient of a solar module. This has produced Si solar modules with temperature coefficients as low as 0.3-0.35 %/C, with the caveat of being more expensive due to higher manufacturing costs. The second path consists in using alternative materials with lower temperature coefficients. Thin-film materials (like CIGS and CdTe) exhibits temperature coefficients as low as 0.2 %/C, which are considerably lower than that of Si modules. Although thin-film modules have also a competitive price, their low efficiencies and reduced durability represent today strong limiting factors, which are ultimately discouraging their use.

Are we then, out of options? No! We at Solar Bankers undertook a different path, focusing on the source of the problem, the light, rather than solar cell materials. The sunlight is made of different colors, also called wavelengths, which together compose the sunlight spectrum. Among these wavelengths there are visible and invisible, infrared (IR) colors. Silicon solar modules can convert the visible spectrum and only a small portion of the IR light. The remaining wavelengths pass undisturbed trough silicon, but are turned into heat at the electrodes, which cover the back surface of solar cells. As a result, not only these wavelengths are not converted into useful electricity, but they also reduce the performance of the module, as they increase its operative temperature. Solar Bankers developed and patented a high-tech solution to get rid of unwanted, efficiency-lowering wavelengths, thus achieving better performance than standard modules even in high-temperature environments. The product consists in a nanostructured optical film that efficiently selects the light colors suitable for photovoltaic conversion and bends away those that only produce heat. Field test have confirmed that Solar Bankers film can reduce the difference between the module operating temperature and that of the ambient by almost 35%, leading to the recovery of the previously lost power output of up to 30% depending on solar cell quality.

Now you might be thinking, “Great news, but I have already installed many MW and I am still paying for them!” Our patented technology can be added to existing solar panels, making it easier for you to upgrade your solar farm. Read more about how our technology can help you in www.solarbankers.com/technology.html or contact us! Stay tuned for more tips on how to increase the performance of your solar panels! And don’t forget to follow us on Twitter!

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s